Compound Operators

Compound operators combine an arithmetic or bitwise operation with assignment, letting you write x += 5 instead of x = x + 5. The increment ++ and decrement -- operators are shorthand for adding or subtracting 1. These operators make your code more concise and are widely used in loops and counters.

++ (increment)

The ++ operator adds 1 to a variable. In prefix form (++x), it increments before the value is used. In postfix form (x++), it increments after the value is used.

void setup() {
  Serial.begin(9600);
  int count = 0;

  Serial.println(count++);  // prints 0, then count becomes 1
  Serial.println(++count);   // count becomes 2, then prints 2
  Serial.println(count);     // prints 2
}

void loop() {
  // nothing to do here
}

In this example, count++ (postfix) returns the current value (0) before incrementing, while ++count (prefix) increments first and then returns the new value (2). In a for loop like for (int i = 0; i < 10; i++), the postfix form is conventional.

– (decrement)

The -- operator subtracts 1 from a variable. Like ++, it has prefix (--x) and postfix (x--) forms with the same timing difference.

void setup() {
  Serial.begin(9600);
  for (int i = 5; i > 0; i--) {
    Serial.println(i);  // prints 5, 4, 3, 2, 1
  }
  Serial.println("Liftoff!");
}

void loop() {
  // nothing to do here
}

This countdown loop uses i-- to decrement from 5 down to 1. Decrement is less common than increment but useful for reverse loops, removing items from a stack, or counting down remaining time.

+= (compound addition)

The += operator adds the right value to the left variable and stores the result back in the left variable. It is equivalent to x = x + y.

void setup() {
  Serial.begin(9600);
  int total = 0;

  for (int i = 1; i <= 5; i++) {
    total += i;  // same as total = total + i
  }
  Serial.println(total);  // prints 15 (1+2+3+4+5)
}

void loop() {
  // nothing to do here
}

This sketch sums the numbers 1 through 5 using +=. Compound operators reduce repetition and make the intent clearer than the expanded form.

-= (compound subtraction)

The -= operator subtracts the right value from the left variable and stores the result.

void setup() {
  Serial.begin(9600);
  int fuel = 100;

  for (int i = 0; i < 3; i++) {
    fuel -= 25;  // same as fuel = fuel - 25
    Serial.println(fuel);
  }
  // prints 75, 50, 25
}

void loop() {
  // nothing to do here
}

This example simulates fuel consumption in three steps. Compound subtraction is useful for countdowns, decreasing health points, or draining battery levels.

*= (compound multiplication)

The *= operator multiplies the left variable by the right value and stores the result.

void setup() {
  Serial.begin(9600);
  int value = 2;
  for (int i = 0; i < 4; i++) {
    value *= 2;  // same as value = value * 2
    Serial.println(value);
  }
  // prints 4, 8, 16, 32
}

void loop() {
  // nothing to do here
}

This sketch demonstrates exponential growth - each iteration doubles the value. Compound multiplication is useful for scaling values, calculating powers of two, or applying gain factors.

/= (compound division)

The /= operator divides the left variable by the right value and stores the result. Remember that integer division truncates.

void setup() {
  Serial.begin(9600);
  int steps = 100;

  for (int i = 0; i < 3; i++) {
    steps /= 2;  // same as steps = steps / 2
    Serial.println(steps);
  }
  // prints 50, 25, 12 (truncated)
}

void loop() {
  // nothing to do here
}

Here, the value is halved each iteration. Note that 12 is the truncated result of 25 / 2. Use float types if you need fractional results from compound division.

%= (compound remainder)

The %= operator computes the remainder of dividing the left variable by the right value and stores the result.

void setup() {
  Serial.begin(9600);
  int value = 17;
  value %= 5;  // same as value = value % 5
  Serial.println(value);  // prints 2
}

void loop() {
  // nothing to do here
}

Compound remainder is useful for wrapping values within a range. For example, cycling through LED indices: currentLED = (currentLED + 1) % 10; can be written as currentLED += 1; currentLED %= 10;.

&= (compound bitwise AND)

The &= operator performs a bitwise AND between the left variable and the right value, storing the result. It is commonly used to clear specific bits.

void setup() {
  Serial.begin(9600);
  byte flags = 0b11111111;
  flags &= 0b00001111;  // clear upper 4 bits
  Serial.println(flags, BIN);  // prints 1111
}

void loop() {
  // nothing to do here
}

This example masks the upper 4 bits of flags, keeping only the lower 4 bits. &= is useful for clearing specific bits by ANDing with a mask that has 0s in the positions you want to clear.

|= (compound bitwise OR)

The |= operator performs a bitwise OR between the left variable and the right value, storing the result. It is commonly used to set specific bits.

void setup() {
  Serial.begin(9600);
  byte flags = 0b00000000;
  flags |= 0b00000101;  // set bits 0 and 2
  Serial.println(flags, BIN);  // prints 101
}

void loop() {
  // nothing to do here
}

Here, bits 0 and 2 are set to 1 while other bits remain unchanged. The |= operator is commonly used to enable features by setting bits in hardware control registers.

^= (compound bitwise XOR)

The ^= operator performs a bitwise XOR between the left variable and the right value, storing the result. XOR flips bits that are 1 in the mask.

void setup() {
  Serial.begin(9600);
  byte flags = 0b00001111;
  flags ^= 0b11111111;  // flip all bits
  Serial.println(flags, BIN);  // prints 11110000

  // Toggle a specific bit
  byte ledState = 0b00000001;
  ledState ^= 0b00000001;  // toggle bit 0
  Serial.println(ledState, BIN);  // prints 0
  ledState ^= 0b00000001;  // toggle again
  Serial.println(ledState, BIN);  // prints 1
}

void loop() {
  // nothing to do here
}

XOR with ^= is useful for toggling bits - applying the same mask twice restores the original value. This makes it ideal for tasks like blinking an LED by toggling its control bit.